Standard Specifications

• RCD 2 (Recreational Craft Directive 2013/53/EU) exhaust emission compliant.
• EPA (U.S Environmental Protection Agency) Tier III – 40 CFR 1042 exhaust emission compliant. Note: Extra charges apply and this must be specified at time of order.
• Mechanically governed comes with:
  • Heat exchanger, header tank and water cooled exhaust manifold.
  • Fresh and sea water pump, injection bend for a wet exhaust.
  • Mechanical fuel lift pump, fuel and oil filtration.
  • Flywheel housing and drive plate with heavy inertia ring for super smooth running at low rpm.
  • Special quiet air intake filter.
• 70 Amp, 12 Volt battery charging alternator.
• Complete with ‘ABV’ control panel with tachometer with running hour recorder, keystart switch, push button stop, green light for ‘power on’, red warning lights and audible alarm for: low oil pressure, high water temperature and engine alternator ‘no charge; 3m interconnection cable with multi pin plug connector.
• Heavy duty engine feet and flexible mountings.
• R&D flexible coupling.
• ‘Morse’ type end fittings for engine speed and gearbox control.
• Engine test certificate and operators manual.
• Beta red paint.

Gearbox Options & Technical Drawings

Beta Marine offer the following standard gearbox options and reduction ratios. Gearboxes have been selected to match the torque loading of each engine and will be correct for the majority of yachts, motor sailors or motor boats. Find out more…

Bobtail – No Gearbox
Bobtail Engine with Drive Plate & Housing Only	Standard

Technodrive / Twin Disc
TMC60 – Mechanical	Standard
TMC60A – 7° Down Angle, Mechanical	Standard

PRM Marine
PRM125 – Mechanical	Standard
PRM150 – Hydraulic	Standard
PRM280 – Hydraulic	Optional
PRM260C – In-line Hydraulic	Optional

ZF
ZF15MIV – 15° V Drive, Mechanical	Standard

Control Panel Options

Beta Marine offer a range of control panels to cater for various requirements. Click on any of the thumbnail images to view a larger more detailed image of the control panel. Find out more…

Electrical Options

We offer a selection of different alternator options (subject to additional cost) to suit most requirements for heat exchanger engine use. However, if you require an alternative solution with specific alternators we can usually design, manufacture and fit suitable alternator supports and pulley drives to suit your needs. Find out more…

Note: Minimum recommended battery: Not included.

12v 70Ah 450CCA

12 Volt Alternators
70 Amp, 12 Volt Alternator	Standard
120 Amp, 12 Volt Alternator in Lieu of Standard	Optional
70 Amp, 12 Volt Insulated Return Alternator in Lieu of Standard	Optional
120 Amp, 12 Volt Secondary Domestic Alternator	Optional
125 Amp, 12 Volt Split Charging System	Optional

Travel Power
3.5 kVA Travel Power – 230 Volt, Single Phase 50Hz	Optional

Shallow Sump Options

For vessels with very limited space between the engine, bearers and hull we can offer a specially designed shallow sump option. The key differences are a reshaped sump pan and repositioning of the sump pump connection.

Oil volumes are marginally reduced (please refer to relevant operators manual) but the dip stick calibration is unchanged. However when this option is fitted, it is important to note that the frequency of the oil change period is reduced. Rather than the standard oil change hours of use, engines fitted with a shallow sump require an initial change after 50 hours then either annually or every 150 hours if sooner.

Special Feet Service

Beta Marine engines have been fitted into tens of thousands of vessels around the world using our standard engine feet. However engine bearers can vary immensely so when a problem arises, our solution is to offer our unique service of designing and manufacturing “Special Engine Feet” to suit your individual engine bearers.

Having designed, manufactured and supplied thousands of bespoke “Special Feet” when required, the additional cost of this option is heavily repaid when your new engine just drops onto your existing engine bearers and lines up with your propeller shaft reducing installation complexity, time and labour. Find out more…

Accessories

Beta Marine seagoing propulsion engines are complemented by a complete range of installation accessories. Find out more…

Literature & Manuals

Beta 35 – Beta 45T
Illustrated Parts List

TMC60 Gearbox
Operators Maintenance Manual

TMC60A Gearbox
Operators Maintenance Manual

PRM125 Gearbox
Operators Maintenance Manual

PRM150 Gearbox
Operators Maintenance Manual

PRM280 Gearbox
Operators Maintenance Manual

PRM260C In-Line Gearbox
Operators Maintenance Manual

ZF15MIV Gearbox
Operators Maintenance Manual

Dealer Network

Beta Marine Canada authorised dealers maybe found within the interactive map below. If your province or city has no convenient nearby dealer, please contact us to discuss your requirements.

Online Enquiry Form

If you are human, leave this field blank.

Your Name *

Company

(If Applicable)

Contact Phone *

Address

Contact Email *

Country *

Confirm Email *

Enquiry or Comments

Type of Vessel

Length of Vessel (Waterline Length)

Current Engine Type and Power

Where Will Your Vessel be Moored During Installation *

Submit

*

reCAPTCHA is required.